TMS320C6713 DSP Module for PMC

Product Details:

Related Information:

SI-C6713DSP-PMC: Technical Specification

Texas Instruments TMS320C6713

	32 bit Floating Point Signal Processor
	225-300Mhz Clock Frequency
	16 DSP DMA channels
	2 PCI DMA channels

SDRAM program and data memory:

	Standard 3.3V, non-buffered PC133 SO-DIMM format.
	Sizes: 64MB, 128MB, 256MB and 512MB, with x16 organizations. Only half of capacity is used.
	PC133 SDRAM module clocked from E Clock running at 75Mhz, maximum delay of memory ICs mounted on module not to exceed 7.5 nsec.
	Single bank SO-DIMMs: supports half of memory ICs mounted on single bank modules, with all capacity only mapped on CE2 (DSP memory region starting at 0xA0000000). The DSP's CE3 region is left empty (DSP memory region starting at 0xB000000).
	Dual bank SO-DIMMs: supports half of memory ICs mounted on dual bank modules, with quarter of module capacity mapped on CE2 (DSP memory region starting at 0xA0000000), and the second quarter mapped on CE3 (DSP memory region starting at 0xB000000). Remaining capacity is ignored.
	Host accessible while DSP is active, with multiple communication options.

Boot memory:

	512kx8 SRAM or 2Mx8 Flash memory.
	Configured as Dual Access memory: Accessible by host (only while DSP is inactive/reset) for downloading COFF files. Accessed by DSP during its boot loading process.
	Mapped on CE1 (DSP memory region starting at 0x90000000).

PCI initiated bus master transfer speeds:

	Up to 132Mbyte/sec bursts with block sizes of eight (8) 32 bit words.
	Up to 25Mbyte/sec sustained transfers of any block size, using DMA.

PCI Bus Bridge PCI9054:

The PCI9054's internal registers are tied onto the C6x's EMIF bus, mapped on CE0 (DSP memory region starting at 0x80000000).

Eight 32 bit, bi-directional communications modes between TMS320C6x and the PCI9054:

	Host target/slave access mode, combined with DSP I/O or DSP's DMA engine.
	Block Mode DMA Bus Master mode, using the PCI9054 as the PCI bus master, combined with DSP I/O or DSP's DMA engine.
	PCI Initiated/Local Master with the DSP as the PCI bus master, with DSP I/O or DSP's DMA engine.

Four C6x routable interrupts:

	Up to three C6x interrupts can be routed for basic communication and DMA synchronization.
	Up to two C6x interrupts can be routed to expansion connectors.

Two 2mm socket connectors, and one external 100 pin half pitch DSUB connector:

	DSP Expansion: First external 2mm pitch, 5x30 (150 contacts) socket connector for interfacing the expansion board to the DSP's bus, or linking to all of the DSP's peripheral ports (McBSP, McASP, HPI/GPIO, Timers).
	User I/O: Second external 2mm pitch, 4x30 (120 contacts) socket connector for interfacing external user defined signals to custom daughter board. Linked only to externally accessible 100 pin half pitch DSUB connector.
	External 100 pin, half pitch (0.050"), Series III DSUB connector for interfacing external user defined signals to the 2mm User I/O connector. AMP part 787169-9, 787170-9, or 787362-9.

DSP Expansion 2mm connector decodes 64Kx32 words, mapped into the DSP's EMIF bus, which contains the following signals:

	Address: A[15:0] (DWord Boundary).
	Data: D[31:0].
	Control: X_R/Wn, X_CSn, X_INT[1:0] (software routable to DSP's EXTINT[7:4]), X_RDY, X_CLK[1:0].
	Peripheral Ports: McBSP[1:0], HPI/GPIO, TINP[1:0], TOUT[1:0].
	Host +3.3Vdc, +5Vdc, +/-12Vdc, +1.8Vdc and GND.

Miscellaneous Connectors:

	One 50 pin header (2x25): McBSP1, TINP[1:0], TOUT[1:0].
	One 10 pin header (2x5): McBSP0.
	One 14 pin header for JTAG port.

	Windows and Linux 32/64 bit driver support.
	Extensive QuVIEW DSP-resident libraries for LabVIEW, including examples for real time acquisition, signal processing, and control.
	Extensive QuBASE DSP-resident libraries for Visual Basic, including examples for real time acquisition, control and analysis.
	Sample code for COFF loaders, PC <-> DSP communications source code and SI-DDK.
	Compatible with separately purchased TI debuggers, C/C++ compilers, assemblers and linkers.

	PMC card measuring 5.86"(L) x 2.9"(H) or 149cm(L) x 74cm(H).
	0.18lbs or 85 grams.
	Supply Voltages: 3.3V for all circuitry, and 5V for expansion bus buffers; 3V expansion buffers may be placed on special request. +/-12V supplies passed on to expansion connector and not used by onboard circuitry.
	4.5 watts (3.3V @ 1.5A) typical with 128MB SDRAM.
	Commercial grade 0-85C. Consult factory for availability of industrial and military temperature grades.